| bcd |
Boat Data |
| OPTIONAL SAILS | If no flying sails are selected, then the certificate will have only Non-Spinnaker ratings. | text |
| I | The height of the permanent headstay mast termination above the sheer line. Typically, IG = I. | length |
| ORR CERTIFICATE NUMBER | | text |
| BDY | | length |
| EB | | length |
| IG | The height of highest Genoa/Jib termination point above the sheer line. | length |
| LOA | The overall length of the boat including the whole hull. Do not include spars or projections fixed to the hull such as chainplates, bowsprits, boomkins, pulpits, etc.. | length |
| WHISKER POLE | Is a whisker pole set to windward (opposite the boom) used to sheet the headsail in a wing-and-wing configuration? | text |
| LWL | The length of the hull at the waterline. | length |
| ANCHOR DIST | | length |
| BEAM MAX | The maximum width (beam) of the boat measured at deck level at the widest point between the port and starboard sides. | length |
| SA/D DNWIND | A sailboat metric for express a Power to Drag ratio. Downwind SA/D = Downwind Sail Area/(displacement)^.667 | number |
| ISP | The height of highest spinnaker termination point above the shear line. | length |
| ISPA | If different from ISP, the height of asymmetric spinnaker halyard hoist point above the sheer line. | length |
| ISPN | The height of highest narrow asym spinnaker halyard hoist point above the sheer line. | length |
| MW | | length |
| ILRH | The height of Large Roach Headsail termination point above the sheer line. | length |
| SA/D AVERAGE | | number |
| BASY | | length |
| DRAFT | The maximun depth of the boat (keel) below the waterline. | length |
| J | The distance between the front of the mast and the headstay termination on the deck at the sheer line. | length |
| JLRH | The distance between the front of the mast and the Large Roach Headsail tack point at the sheer line. | length |
| SA/D UPWIND | | number |
| SA/D | | number |
| JG | Typically, JG = J. The horizontal distance from the forward face of the mast to the Jib/Genoa tack point. | length |
| BAS | Boom Above Sheer | length |
| DRAFT SHOAL | The shallowest Draft possible during sailing. | length |
| P | The distance between colored bands on the mast, or the maximum luff length of the Mainsail. | length |
| RIG TYPE | The type (style) of rig the boat uses. | ● Sloop,
● Ketch,
● Yawl,
● Gaff,
● Cat Ketch,
● Cat,
● Cutter,
● Schooner,
● Other,
|
| D/LENGTH | Boat Metric for comparing designs and Speed. DLR = Displacement/(LWL)^3 | text |
| D/LENGTH | Boat Metric for comparing designs and Speed. DLR = Displacement/(LWL)^3 | text |
| DISPLACEMENT | The total weight (displacement) of the boat. Enter either the manufacturers published data or, if the boat has been weighed, the actual measured weight. | weight |
| DISP EMPTY | The dry weight of the boat with all loose equipment removed. This is undoubtedly the most frequent question by owners since in almost all cased the "Measured Displacement" used for ORR-Ez ratings is greater than the "Brochure Displacement" used for publications and posted on Sailboatdata.com ORR-Ez uses the median of the boats that have been measured for ORR,ORC,IRC, Americap, IMS | weight |
| E | The distance between the colored bands on the boom, or the maximum foot length of the Mainsail. | length |
| FORESTAY | Choose Masthead if the headstay terminates at the top of the mast. Choose Fractional if the headstay terminates anywhere below the top of the mast. | ● Masthead,
● Fractional,
|
| OFFSETS_FILE | | text |
| CREW | The aggregate weight of the crew in lightweight clothing used in the calculations of ratings. This is the Maximum Crew Weight and any excess shall automatically suspend the validity of the Certificate. | weight |
| WATER BALLAST | | weight |
| CREW WEIGHT METHOD | Declared or Default. | text |
| EY | The distance between colored bands on the boom, or the maximum foot length of the Mizzen. | length |
| HULL MATERIAL | The primary hull material. | ● Light or Other,
● Fiberglass Cored,
● Cored Glass,
● Fiberglass,
● Fiberglass Solid,
● Solid Glass,
● Aluminum,
● Wood,
● Carbon FIber,
● Carbon,
● Other,
● Carbon Nomex,
● Carbon Heavy,
● Carbon Solid,
|
| AVE PERF SCREEN | Average perf screen is a metric that is used by some OA's for establishing fleet splits that are based on the 'Sportiness' of a boat. Mathematically it is Average Sail Area Displacement Ratio / Displacement Length Ratio * 100 to make it readable. | number |
| PERF SCREEN | Average perf screen is a metric that is used by some OA's for establishing fleet splits that are based on the 'Sportiness' of a boat. Mathematically it is Average Sail Area Displacement Ratio / Displacement Length Ratio * 100 to make it readable. | number |
| DECLARED CREW WEIGHT | Crew Weight as declared by the applicant or in accordance with OD class rules. | weight |
| DEFAULT CREW WEIGHT | Final Default Crew Weight is calculated by the VPP and will not precisely match the Estimated Crew Weight shown on the application. | text |
| ESTIMATED CREW WEIGHT | Estimated Crew Weight is based on Diplacement and LWL values.
The final value will be calculated once the ORR-ez VPP is run. | weight |
| KEEL TYPE | The type (style) of keel on the boat. | ● Fixed w/ Winglets,
● Fixed,
● Canting,
● Fin,
● Centerboard,
● Keel Centerboard,
● Fin with Bulb,
● Wing,
● Other,
|
| PY | The distance between colored bands on the mizzen mast, or the maximum luff length of the Mizzen. | length |
| KEEL MATERIAL | The primary keel material(s). | ● Lead,
● Steel/Lead,
● Iron,
● Other,
|
| PROP TYPE | The type (style) of propeller the boat uses; or to indicate the use of an Outboard motor. | ● Fixed,
● Folding,
● Feathering,
● Outboard,
● None,
|
| SPL | The length of the spinnaker pole (or whisker pole), when it is attached on the mast, and set in a horizontal position fore and aft, measured from the forward face of the mast to the forward most point of the pole and fittings. | length |
| PROP INSTALL | The type (style) and placement of mounting for the propeller. Note that Strut Drive is the proper choice for Sail Drives. | ● Exposed,
● In Aperture,
● Strut Drive,
● Other,
● Exposed Other,
● Exposed Twin,
● Housed Shaft,
● Pre 1987,
● Old Strut,
● Exp No Strut,
● No Prop,
|
| TPS | The tack point of an asymmetric spinnaker (mounted on the centerline of the boat, to the deck or to a sprit) measured from the front of the mast to the tack point of the sail, perpendicular to the water. | length |
| TPSN | If different from TPS, the horizontal measurement from the forward face of the mast to the narrow asym spinnaker tack point. | length |
| ANCHOR & RODE WEIGHT | Total weight of the Anchor, Chain and Rode. | weight |
| PROP BLADES | The number of blades the propeller uses. | ● 2,
● 3,
● 4,
|
| SFJ | Distance from the headstay deck termination, forward to the hull stem point. Typically positive or zero, but may be negative, for example a cutter rig with a bow platform. | length |
| MDL1Y | | length |
| OUTBOARD WEIGHT | Total weight of the Outboard motor, without fuel. | weight |
| STAB INDEX | | degree |
| HIKING STRAPS? | Boat has hiking straps? | text |
| MAST SIZE | Some boats (models) are supplied with different hight masts. Choose standard unless yours is known to be taller or shorter than standard. | ● Standard,
● Tall,
● Short,
|
| MAST MATERIAL | The material that the mast is made of. | ● Aluminum,
● Carbon,
● Wood,
|
| TRAPEZE? | Boat has trapeze(s)? | text |
| SPINNAKER | The type of spinnaker(s) this boat flies. Include all types. | ● None,
● Asym only on centerline,
● Asymmetrical tacked centerline on bow, sprit or prod,
● Asym only on moveable pole,
● Asymmetrical only flown with spinnaker pole,
● Symm only on moveable pole,
● Symmetrical flown with spinnaker pole,
● Symm & Asym on moveable pole,
● Both Symmetrical & Asymmetrical flown with spin pole,
● Symm on pole & Asym on centerline,
● LRH only, no Spinnaker,
|
| CODE ZERO | Answer Yes if you carry a spinnaker with a midgirth-to-foot measurement ratio of less than 85% but not less than 75%. | ● No,
● Yes,
|
| GENOA/JIB LEECH | No Roach: No width measurements (LP only);
Has Roach: Has width measurements (roach may be convex or concave). | ● No Roach - Leech is straight,
● Has Roach or Hollow,
|
| LARGE ROACH HEADSAIL | Answer Yes if you carry a headsail with a midgirth-to-foot measurement ratio of greater than 50% but less than 75%. | ● No,
● Yes,
|
| MDL1 | | length |
| MDL2Y | | length |
| TACK | Where is the Asym Spin tacked?
Centerline includes bow, fixed sprit or retractable sprit.
Moveable Pole is a typical symmetric spinnaker pole.
Articulating Sprit is a bowsprit that can pivot to windward. | ● Moveable Pole,
● Centerline,
● Articulating Sprit,
● --pick one--,
|
| NARROW ASYM 75-85% | AKA: Code 0 Spinnaker. Do you carry a narrow asym spinnaker with a SHW / SFL ratio between 75% and 85%? | ● No,
● Yes,
|
| TACK | Where is the Narrow Asymmetric Spinnaker tacked? | ● Moveable Pole,
● Centerline,
● Articulating Sprit,
● --pick one--,
|
| JIB FURLER | Does the genoa/jib (headsail) use a roller furling device? | ● Yes,
● No,
● Yes Above Deck,
● Yes Below Deck,
|
| TLY | | length |
| MAIN ROLLER FURLING | Does the Main use a roller furling device? | ● No,
● Yes In Mast,
● Yes In Boom,
|
| MDL2 | | length |
| TL | | length |
| OUTRIGGER | Is an Outrigger or Whisker Pole set to leeward used to sheet the headsail outboard of the sheerline? | number |
| BD | | length |
| SPRIT PIVOT | Distance from the articulating sprit pivot point to the sprit tip (TPS meas point). | length |
| SPRIT ANGLE MAX | Maximum articulating sprit angle relative to centerline. | degree |
| calc |
Calculated |
| VPP AREA SYMM | | text |
| VPP AREA GENOA/JIB | | text |
| VPP AREA LRH | | text |
| VPP AREA SYMM | | text |
| VPP AREA NARR | | area |
| VPP AREA SYMM | | text |
| RATED LENGTH | The Rated Length of a boat is the effective sailing length used to predict boat speeds and ratings. This is calculated in the sailing conditions which includes crew, gear and sails. It includes the effects of bow and stern overhangs. | length |
| AREA | The total area (square feet/meters) of the largest Symmetrical Spinnaker. | area |
| DISP SAILING | The calculated displacement of the boat in sailing configuration, including equipment and crew. | weight |
| AREA | The total area (square feet/meters) of the largest Mainsail. | area |
| AREA | The total area (square feet/meters) of the Mizzen. | area |
| WETTED AREA | | area |
| LPS | | degree |
| AREA | The total area (square feet/meters) of the largest Asymmetrical Spinnaker. | area |
| AREA | The total area (square feet/meters) of the largest Asymmetrical Spinnaker. | area |
| RM20 | | force |
| AREA | The total area (square feet/meters) of the largest Headsail (Jib or Genoa). | area |
| AREA | The total area (square feet/meters) of the largest Large Roach Headsail. | area |
| jibs |
Jib Data |
| GENOA/JIB USED | | text |
| JIB LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Headsail (genoa/jib) should be supplied. | text |
| GENOA/JIB OBOSLETE | | text |
| LP | The shortest distance from the clew of the Jib to the luff. | length |
| LP SOURCE | | length |
| LPG % | The width (LP) of the headsail expressed as a percentage of the J measurement. | percentage |
| J LUFF | The length of the luff shall normally be the distance between the lowest part of the sail of the luff at the tack and the highest point of the sail on the luff at the head. | length |
| J LEECH | | length |
| JH | The width of the Jib/Genoa head or headboard. | length |
| JMGT | The shortest distance from the seven-eighths leech point of the Jib/Genoa perpendicular to the luff. | length |
| JMGU | The shortest distance from the three-quarter leech point of the Jib/Genoa perpendicular to the luff. | length |
| JMGM | The shortest distance from the half leech point of the Jib/Genoa perpendicular to the luff. | length |
| JMGL | The shortest distance from the quarter leech point of the Jib/Genoa perpendicular to the luff. | length |
| SAIL MAKER ID | | text |
| main |
Mainsail Data |
| MAIN USED | | text |
| MAIN LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Mainsail should be supplied. | text |
| MAIN OBOSLETE | | text |
| HB | The width of the Mainsail Headboard. | length |
| MGT | The shortest distance from the seven-eighths-leech point of the Mainsail to the luff. | length |
| MGU | The shortest distance from the three-quarter-leech point of the Mainsail to the luff.
| length |
| MGM | The shortest distance from the half-leech point of the Mainsail to the luff. | length |
| MGL | The shortest distance from the quarter-leech point of the Mainsail to the luff. | length |
| SAIL MAKER ID | | text |
| asym |
Asym Data |
| SYMM USED | | text |
| ASYM LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Asymmetrical Spinnaker should be supplied. | text |
| SYMM OBOSLETE | | text |
| ASLU | The Asymmetrical spinnaker luff length. | length |
| ASLE | The Asymmetrical Spinnaker leech length. | length |
| AMG | The measurement between the midpoints of the Asymmetrical Spinnaker luff and leech. | length |
| ASF | The Asymmetrical Spinnaker foot length. | length |
| SAIL MAKER ID | | text |
| symm |
Spinnaker Data |
| SYMM USED | | text |
| SYM LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Symmetrical Spinnaker should be supplied. | text |
| SYMM OBOSLETE | | text |
| SL | The longest length of a Symmetric Spinnaker luff and leech measured along the edges of the sail from head to foot. | length |
| SMW | The Symmetrical Spinnaker measurement between the midpoints of the luff and leech. | length |
| SF | The Symmetrical Spinnaker distance between the tack and clew, measured by the shortest path. | length |
| SAIL MAKER ID | | text |
| narr |
|
| NARR USED | | text |
| NARR LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. | text |
| NARR OBOSLETE | | text |
| SLU | The Narrow Asymmetrical spinnaker luff length. | length |
| SLE | The Narrow Asymmetrical Spinnaker leech length. | length |
| SHW | The measurement between the midpoints of the Narrow Asymmetrical Spinnaker luff and leech. | length |
| SFL | The Narrow Asymmetrical Spinnaker foot length. | length |
| SAIL MAKER ID | | text |
| mizz |
Mizzen Data |
| MIZZ ID | | number |
| MIZZ LOCKED | | text |
| MIZZ OBSOLETE | | text |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Mizzen should be supplied. | text |
| HBY | The width of the Mizzen headboard. | length |
| MGTY | The shortest distance from the seven-eighths-leech point of the Mizzen to the luff. | length |
| MGUY | The shortest distance from the three-quarter-leech point of the Mizzen to the luff. | length |
| MGMY | The shortest distance from the half-leech point of the Mizzen to the luff. | length |
| MGLY | The shortest distance from the quarter-leech point of the Mizzen to the luff. | length |
| lrhs |
Lg Roach Headsail Data |
| LRH LOCKED | | text |
| MFR. DATE | | date |
| DESC | This field is for informational purposes only. You can use it to clarify which sail you are asking the sail maker to provide measurements for. NOTE for ORR-ez only, the information of your largest Large Roach Headsail should be supplied. | text |
| LRH OBOSLETE | | text |
| HB | The width of the Large Roach Headsail head or headboard. | length |
| TW | The shortest distance from the seven-eighths-leech point of the Large Roach Headsail to the luff. | length |
| UW | The shortest distance from the three-quarter-leech point of the Large Roach Headsail to the luff. | length |
| MW | The shortest distance from the half-leech point of the Large Roach Headsail to the luff. | length |
| LW | The shortest distance from the quarter-leech point of the Large Roach Headsail to the luff. | length |
| FOOT | The length of the foot of the Large Roach Headsail. | length |
| MG | The measurement between the midpoints of the Large Roach Headsail luff and leech. | length |
| LP | The shortest distance from the clew of the Large Roach Headsail to the luff. | length |
| LUFF | The length of the luff shall normally be the distance between the lowest part of the sail of the luff at the tack and the highest point of the sail on the luff at the head. | length |
| LEECH | The length of the leech of the Large Roach Headsail. | length |
| SAIL MAKER ID | | text |
| stay |
Mizzen Staysail |
| STAYSAIL | | date |
| STAY LOCKED | | text |
